|
|
Section:
1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
|
| 1.0 INTRODUCTION |
 |
1.1
About This Technical Guide
1.2
Total Customer Satisfaction
1.3
General Information
| 2.0 FASTENING
TECHNOLOGY--GENERAL INFORMATION |
|
2.1
Base Materials
2.2
Evaluation of Test Data
2.3
Corrosion
3.1 Powder Actuated Fastening
Technology
3.1.1 DX Selector Guide
3.1.2 Fastening to Concrete
3.1.3 Fastening to Steel
3.1.4 Fastener Corrosion Resistance
3.1.5 DX Kwik System
3.2 Powder Actuated Fasteners
3.2.1 General Application Fasteners
(X-CF, X-ZF, X-DNI, DS, Threaded Studs, X-AL-H, X-CR
Nails and Threaded Studs)
3.2.2 Special Application Fasteners
(Ceiling Clips, EMT Clips, X-IR, X-IE, Cable Clips,
Forming Nail)
3.2.3 DX Fastener Technical Data
3.2.4 Powder Actuated Fastener
Listings and Approvals
3.2.5 Powder Actuated Fastener
Specifications
3.3 DX Siding and Decking Systems
3.3.1 Hilti Fasteners for Attaching
Metal Siding or Decking
3.3.2 Hilti DX Siding and Decking
Tools
3.3.3 Fastener Selection Guide
3.3.4 Fastener Selection Guide
Worksheet
3.3.5 Fastener Quantity Estimation
Table
3.3.6 Siding and Decking Fastener
Technical Data
3.3.7 Diaphragm Tables for Deck
Fasteners
3.3.8 Siding and Decking Fastener
Specifications
3.4 X-HVB Shear Connector
3.5 Grating Disk Fastening System
(Stainless Steel, Hot-dipped Galvanized, Electro-galvanized)
| 4.0 ANCHORING SYSTEMS |
|
4.1 Anchoring Technology
4.1.1 Anchor Terminology
4.1.2 Anchor Principles
4.1.3 Anchor Design Considerations
4.1.4 Anchor Selector Guide
4.1.5 Hilti Anchor Program
4.2 Adhesive Anchoring Systems
4.2.1 HVA Adhesive Anchor Systems
4.2.2 HIT HY-150 Adhesive Anchor
Systems
4.2.3 HIT HY-20 Adhesive Anchor Systems
4.2.4 HSE 2411 Epoxy Anchor Systems
4.3 Mechanical Anchoring Systems
4.3.1 HUC Undercut Anchor
4.3.2 HSL Heavy Duty Sleeve Anchor
4.3.3 Kwik Bolt II Expansion Anchor
4.3.4 HDI Drop-In Anchor
4.3.5 HDI-P Drop-In Anchor
4.3.6 Sleeve Anchor
4.3.7 Metal HIT Anchor
4.3.8 HPS-1 Impact Anchor
4.3.9 Toggler Bolt
4.3.10 HLD Kwik Tog
4.3.11 HDS Drywall Anchor
4.3.12 PSA Plastic Screw Anchor
4.3.13 IDP Insulation Anchor
| 5.0 SCREW FASTENING SYSTEMS |
|
5.1
Corrosion Protection for Screws
5.2 Self-Drilling Screws for Metal
5.2.1
Self-Drilling Screw Selection Guide
5.2.2
Kwik-Pro Self-Drilling Screws
5.2.3
Kwik-Flex Self-Drilling Screws
5.3 Screws for Concrete
5.3.1
Kwik-Con II + Fastening Systems
| 6.0 CONSTRUCTION CHEMICALS |
|
6.1 Chemical Products Selector
Guide
6.2 Concrete Restoration Products
6.2.1 RM700EP Epoxy Repair Mortar
6.2.2 RM710EP Lo-Temp Epoxy Repair Mortar
6.2.3 RM800PC Cement Repair Mortar
6.2.4 CI 060 EP Crack Injection System
6.2.5 CS 300 EP Joint Sealant
6.2.6 CC 400 EP Water-Based Epoxy Seal
6.2.7 CC 410 EP Water-Based Epoxy Skid Proofer
6.2.8 Other Concrete Repair and Coating Products
6.2.9 CG 200 PC Cementitious Grout
6.3 Construction Sealants
6.3.1 CS 2130 Polyurethane Sealant
6.3.2 CF 128 Filler Foam
6.4 Construction Adhesives
6.4.1 CA3600 Solvent-Free High Performance Construction Adhesive
6.4.2 CA3400 Heavy Duty Subfloor Adhesive
6.4.3 CA3200 General Purpose Construction Adhesive
6.5 Firestop Sealants
6.5.1 Fire Stop Technical Information System
6.5.2 Fire Stop Application Selector Guide
6.5.3 Hilti Firestop Systems
6.5.4 Ordering Information
| 7.0 INSTALLATION SYSTEMS |
|
7.1 Installation Systems
7.1.1 Strut
7.1.2 Pushbutton
7.1.3 Saddle Nut and Strut Nut
| 8.0 REFERENCE SECTION |
|
Material Safety Data Sheets (MSDS)
8.1 Approvals/Listings
8.1.1
International Conference of Building Officials (ICBO)
Evaluation Reports
8.1.2 City
of Los Angeles (COLA) Approvals
8.1.3
Metro Dade County Approvals
8.1.4
Underwriters Laboratories (U.L.) Listings
8.1.5
Factory Mutual Research Corporation (FMRC) Approvals
8.1.6
Council of American Building Officials (CABO)
8.1.7
Southern Building Code Conference International
(SBCCI)
8.1.8
California State Fire Marshall Listing Service
8.1.9 City
of New York Approvals (MEA)
8.2 Reference Standards
8.2.1 ASTM
Standards for Materials
8.2.2 ASTM
Plating Standards
8.2.3
Federal Specifications
8.2.4 ANSI
Standards
8.3 Technical References
8.3.1
Metric Conversions and Equivalents
8.3.2
Mechanical Properties of Materials
8.3.3 Bolt
Thread Data
8.3.4 Concrete Reinforcing Bar Data
| 9.0 New Business |
|
Installation Systems
Positioning Systems
Innovation Magazine
|
